What is I-TTL flash for Nikon?
The best part is that Nikon Speedlights are really easy to use, with a full automatic mode, called i-TTL, or Intelligent-Through-The-Lens metering. This means that the camera and flash will communicate with each other and figure out the best exposure that will balance both the subject and the ambient light.
What is the best metering mode for Nikon?
With a dark subject and bright background, if you use highlight-weighted metering, the exposure will be adjusted for the background, throwing the main subject into shadow. Highlight-weighted metering can be used for silhouettes, but matrix metering is a better choice if you want exposure optimized for the main subject.
What is TTL metering in camera?
In photography, through-the-lens (TTL) metering refers to a feature of cameras whereby the intensity of light reflected from the scene is measured through the lens; as opposed to using a separate metering window or external hand-held light meter.
What is the difference between I TTL and TTL?
E-TTL = Evaluative “Through the Lens”, i-TTL = Intelligent “Through the Lens”, P-TTL = Preflash “Through the Lens”. All three are pre-flash based evaluative flash metering systems.
What metering should I use for portraits?
Centre-weighted metering is best suited for any image where your subject is in the centre of the frame, or even where the subject fills the majority of the scene. A typical example of this would be portrait photography or macro photography.
What is TTL flash system?
TTL flash is a system of calculating the correct amount of light from your flash using the information from your camera via “through the lens” metering. Some folks consider it an “automatic” mode for flash.
Should you use TTL flash?
So is TTL flash necessary? The simple answer is yes. If you’re running and gunning all the time, you don’t want to be fidgeting with your Speedlite. TTL changes the flash output for you.
What is metering mode Nikon?
The metering mode determines which areas of the frame are used by the camera to measure subject brightness and how the camera sets exposure.
What metering mode is best for portraits?
Center-weighted metering is the go-to setting for portraits, since it will ,make sure the subject is correctly exposed (“expose for the subject”) without giving much weight to the background. It is more predictable than matrix metering, which means you will get more consistent results.
Which metering mode is best?
In general, evaluative metering is the best mode to leave your camera in. While the shot above is slightly overexposed, it’s about as good as the spot metered one, just in the opposite direction; it’s a hell of a lot better than the center-weighted average image.
What is Nikon matrix metering?
Matrix metering evaluates multiple segments of a scene to determine the best exposure by essentially splitting the scene into sections, evaluating either 420-segments or 1,005 segments, depending on the Nikon D-SLR in use.
What’s the best metering mode for portraits?
For most portrait situations, the Matrix metering mode is ideal. (For more on how metering works, see the “Metering Basics” sidebar.) This mode measures light values from all portions of the viewfinder and then establishes a proper exposure for the scene.
What is a metering mode on Nikon?
A metering sensor. The camera does not simply measure the overall brightness of the frame, but measures brightness separately in multiple areas of the frame. The metering mode determines which areas of the frame are used by the camera to measure subject brightness and how the camera sets exposure.
What is the difference between TTL flash metering and camera metering?
It is very important to remember that the Nikon TTL Flash metering system is not actively coupled to the Camera metering system. Even though these two systems use the same metering sensor in the camera, they act independently. This is definitely not intuitive and not explained well in any documentation that I’ve read.
Is the Nikon D2 backwards compatible with D-TTL?
The D- TTL era lasted four years and Nikon only introduced four DSLRs that use D- TTL exclusively: the D1 family: the D1, D1H and D1X and the subsequent D100 in 2002. However, the entire D2 family is also backwards compatible with D- TTL; in fact, they are the only cameras that are both D- TTL and i- TTL compatible.
What makes Nikon speedlights so special?
Nikon Speedlights can pivot, rotate and even be positioned off-camera, allowing light direction and intensity to be completely controlled. External flashes can illuminate subjects up to 98* feet away, nearly 3 times further than your camera’s built-in flash.