What carb does KTM use?

The 38 H-Series is the recommend carb for all KTM and Husqvarna two stroke dirt bikes that are 125ccs and bigger. It was developed specifically for the 2017 and newer dirt bikes with the balanced engines to get them the fuel they need direct off of idle while maintaining excellent overrev characteristics.

How good is a Lectron carb?

The Lectron 38HV made throttle response crisp, and the bike pulled hard in ever gear. The first ride with the Lectron was a new experience for me and this bike. It was easy to get the front tire up over obstacles and there was more than enough low-end grunt to pull me up the steepest of hills.

Can you use a Lectron carb on a 4 stroke?

*Lectrons are a great choice for riders seeking performance, fuel economy, simplicity and smoother power delivery. *Most 4 stroke engines idle around 1,500 – 2,400 RPMs this is where 4 stroke Lectrons function best but no lower.

Does a Lectron carb have jets?

Although the original Lectron® carburetor of 1974 did not have a power jet, all modern iterations of the design come with at least one or more power jets to provide additional fuel to the mix from mid to top.

Are Lectron carbs fuel injected?

If you want the ease and consistency of a fuel injected 4 stroke but the feeling, weight, and agility of a 2 stroke, buy this carb and put it on your 2 stroke and be done with it! It’s a great product and you won’t be disappointed! Everything with a carburetor needs a Lectron.

How much HP does a Lectron carb add?

The higher velocity also activates the power jet earlier to create a stronger, more tunable mid-range. Lectron’s dyno testing has shown a 20% increase in torque and horsepower at 5000RPM compared to the outgoing 38HV on a KTM 250.

Why have Lectron carbs?

Lectron Fuel Systems manufactures industry-leading carbureted fuel systems built on the principles of performance and simplicity, so you can spend more time riding and less time tuning.

Do you have to adjust a lectron carb?

The flat side must always be facing the motor to do this. Don’t adjust it without running it first. It comes preset from the factory, and tuning it on the stand will not accurately represent conditions when the motor is operating under load at the track or on the trail.

Do you have to adjust a Lectron carb?

How does a Lectron carburetor work?

The Lectron carburetor uses divergence to create “Fuel-Lift”. The shape and contour of the ground surface of the metering rod controls how much fuel is allowed to be drawn up in response to the extremely strong fuel pick-up signal.

Where are Lectron carbs made?

the USA
After all, winners choose Lectrons! Because quality, innovation, and design make these carburettors superior to any other carburettors available on the market. Nearly 46 years of winning and still made in the USA!

How do you lean out Lectron carbs?

To tune the rod, remove the slide and hold the slide to where the rod is pointing towards you. Turning it to the right will richen it. Turning it to the left will lean it.

How long does it take to get a Lectron carb?

Lectron products are built to order and will ship within two weeks of purchase. We only accept cancellations within 24 hours of purchase due to the process involved with building custom carburetors.

How do I know if my 2 stroke is lean or rich?

keeping the engine under a light load (you will only be opening the throttle to 1/2 or so) If the needle is set too rich you will hear a sputtering like the choke is on and the acceleration will be slow. If the clip position is too lean the engine will sound quiet and have a “dead” feeling possibly hesitating.

What carburetor is made in USA?

Every Edelbrock Carburetor is manufactured in the USA and has been specifically designed and tuned by Edelbrock engineers to provide the widest overall torque range.

Do you have to tune Lectron?

Do I need to tune my Lectron? Yes. While the Lectron can compensate for elevation, temperature, etc., it cannot compensate for increased load on the engine. Lectron recommends richening the power jet at least ¾ of a turn, and the metering rod at least half a turn.

Are Mikuni carbs made in Japan?

Mikuni Corporation, our parent company in Japan has been in business for over 91 years and has more than 5,000 employees worldwide. Mikuni’s primary business is to manufacture various types of carburetor and other automotive related products. It is well known as one of the leading manufacturers in the industry.